PSSO Amp Set MK2 for Line-Array M, PSSO
- Производитель: PSSO
- Код Товара: 21293-
-
342.797 ₽
(3.509.31€)
PSSO Amp Set MK2 for Line-Array M
- Stereo PA amplifier with class D circuitry
- Low weight and height due to integrated switch mode power supply
- Reliable power amp with high impulse stability for a wide range of applications (e.g. compact PAs, multi-way PAs, concerts)
- Limiter and speaker switch-on delay
- 3 operating modes can be selected (stereo, parallel or bridged)
- 2 calibrated level controls for precise level adjustment
- Input sensitivity adjustable
- LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
- Highly efficient front-to-rear air routing
- Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
- Speaker outputs via lockable Speaker plugs and screw terminals
- Rugged steel chassis with aluminum front panel
- Rack installation with 2 units
-
10451695 PSSO QDA-4400 4-Channel Amplifier
PA amplifier with SMPS, 4 x 1100 W / 4 ohms, 4 x 650 W / 8 ohms
- 4-channel PA amplifier with class D circuitry
- 4 x 1100 W/4 ohms
- Low weight and height due to integrated switch mode power supply
- Reliable power amp with high impulse stability for a wide range of applications (e.g. compact PAs, multi-way PAs, international concerts)
- Speaker switch-on delay
- 3 operating modes can be selected (stereo, parallel or bridged)
- 4 level controls for precise level adjustment
- Input sensitivity adjustable
- LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
- Complete protection set
- Highly efficient front-to-rear air routing
- Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
- Speaker outputs via lockable Speaker plugs
- Rugged steel chassis with aluminum front panel
-
10451696 PSSO QCA-6400 4-Channel SMPS Amplifier
PA amplifier with SMPS, 4 x 1600 W / 2 ohms, 4 x 1400 W / 4 ohms
- 4-channel PA amplifier with class I circuitry
- 4 x 1400 W/4 ohms
- Low weight and height due to integrated switch mode power supply
- Reliable power amp with high impulse stability for a wide range of applications (e.g. compact PAs, multi-way PAs, international concerts)
- Speaker switch-on delay
- 3 operating modes can be selected (stereo, parallel or bridged)
- 4 level controls for precise level adjustment
- Input sensitivity adjustable
- LED VU meter and LEDs for activated protective circuit (protect), overload (clip), and signal per channel
- Complete protection set against short-circuit, overheat, clipping, overload, DC voltage and VHF signals
- Highly efficient front-to-rear air routing
- Electronically balanced inputs via XLR mounting jacks, with XLR feed-through outputs
- Speaker outputs via lockable Speaker plugs
- Rugged steel chassis with aluminum front panel
- Rack installation with 2 units
- Neutrik Speakon outputs
-
10356362 PSSO DXO-26 PRO Digital Controller
Digital speaker management system with real-time network communication, 2 inputs and 6 outputs
- Digital network speaker management system with 64-bit processing
- Premium components ensure excellent sound-features
- Flexible routing configurations for all standard mono and stereo output operating modes
- 2 analog inputs and 1digital AES/EBU interface (XLR)
- 6 analog outputs (XLR)
- 10-band parametric EQ per input and output
- Parametric filters can be set as Bell, High Shelf, Low Shelf, Notch, Allpass
- Active crossover with Bessel, Butterworth and Linkwitz-Riley filter with slopes up to 24 dB/octave
- The intelligent software for PC and Mac allows convenient control with a computer
- Full configuration and real-time network communication via the built-in Ethernet interface
- Up to 80 user presets storable in the device via software
- Control of all functions also possible via the controls at the front panel
- Alphanumeric LCD screen with 2 lines of 16 characters each
- Input sensitivity digitally adjustable
- Inputs and outputs with 4-digit VU meter
- Mute switch with LED indicator per output
- Up to 2000 ms signal delay adjustable for the inputs and outputs
- Output limiter with adjustable limits and automatic attack and release settings as overload protection for your amplifying system
- Switchable phase (180°)
- Lock function for protecting the program settings
- Rack installation, 1 U
- Windows XP, Vista, 7, 8 and Mac OS X 10.5.8 and better
- Control your speaker systems more flexible than ever with the DXO Control app
- DXO Control for iPad supports all functions of the PC software and is available for free from the app store
- Made in Germany
-
30100150 OMNITRONIC Front Panel Z-19U-shaped, steel,black 1U
U-front panel in different sizes
- 1 mm steel, black, powder-coated
- Weight 465-1350 g (depending on the version)
- Height unit: 1 HE
-
30109192 ROADINGER Rack Profi KM 8U 55cm with wheels
PRO flightcase for 483 mm units (19")
- Profile rails with mounting facility for 483 mm units (19"), e.g. light PA amplifiers, power packs, additional equipment
- Stomped profile rails for cage nuts
- 2 removable covers (double-door version)
- High-quality workmanship with 9 mm multiplex birch wood, dark brown laminated
- Aluminum profile frames (30 mm) with rounded edges
- Three-leg, medium-sized steel ball corners
- 4 x recessed case handles with mounting dish and backing ring
- 4 butterfly lock
- 4 wheels with 2 brakes
- 4 x chrome case handles
- Available in different height units (1 U = 44 mm)
- Made in Europe
Технические характеристики
|
10451685 PSSO DDA-2500 Amplifier |
|
| Power supply: | 100-240 V AC, 50/60 Hz |
| Power output (RMS): | |
| Stereo, parallel at 4 ohms | 2 x 1250 W |
| Stereo, parallel at 8 ohms | 2 x 700 W |
| 8 ohms bridged | 1 x 2500 W |
| Signal-to-Noise ratio: | >100 dB |
| Total harmonic distortion: | <0.15 % |
| Damping factor: | >500 |
| Voltage gain: | 39.7 dB |
| Slew rate: | >10 V/µsec |
| Input sensitivity: | 0.775 V/1.0 V/1.81 V bzw. 39.3 dB/37 dB/32 dB, switchable |
| Input impedance: | 20 kohms (balanced), 10 kohms (unbalanced) |
| Input connectors: | 4 x XLR |
| Output connectors: | 4 x Speaker, 4 x XLR feed-through output |
| Circuitry: | Class D |
| Protection: | Softstart, short-circuit, overheat, overload, clip limit, RF and VHF signals |
| Cooling: | 2 temperature-controlled fans, front-to-rear |
| Controls: | Power switch, input attenuators, mode switch stereo/parallel/bridged, input sensitivity |
| LED indicators: | protect, clip, - 5 dB, - 10 dB, - 20 dB (per channel) |
| Construction: | steel chassis, aluminum front |
| Dimensions: | 483 x 307 x 89 mm |
| Rack installation with 2 U | |
| Weight: | 6.25 kg |
| Power consumption: | 200 W 1/8 power |
| Frequency range: | 20 - 20000 Hz |
| Height: | 8,9 cm |
| Depths: | 30,7 cm |
| Width: | 48,3 cm |
| Power/channel (4 Ohm): | 1250 W |
|
10451695 PSSO QDA-4400 4-Channel Amplifier |
|
| Power supply: | 100-240 V AC, 50/60 Hz |
| Power output (RMS): | |
| Stereo, parallel at 4 ohms | 4 x 1100 W |
| Stereo, parallel at 8 ohms | 4 x 650 W |
| 8 ohms bridged | 2 x 2000 W |
| Signal-to-Noise ratio: | >100 dB |
| Total harmonic distortion: | <0.1 % |
| Damping factor: | >500 |
| Slew rate: | >10 V/µsec |
| Crosstalk: | >65 dB |
| Input sensitivity: | 0.775 V/1.0 V/1.81 V or 39.3 dB/37 dB/32 dB, switchable |
| Voltage gain: | 39.3 dB |
| Input impedance: | 20 kohms (balanced), 10 kohms (unbalanced) |
| Input connectors: | 4 x XLR |
| Output connectors: | 4 x Speaker, 4 x XLR feed-through output |
| Circuitry: | Class D |
| Protection: | Soft start, short circuit, over load, over heat, clip limit, RF and VHF signals |
| Cooling: | 2 temperature-controlled fans, front-to-rear |
| Controls: | Power switch, level control, mode switch (stereo,parallel,bridged), input sensitivity |
| LED indicators: | protect, clip, signal, -5 dB, -10 dB, -20 dB (per channel), dB/V mode |
| Construction: | Steel chassis, aluminum front |
| Dimensions: | 483 x 461 x 91 mm |
| rack installation with 2 U | |
| Weight: | 9.5 kg |
| Power consumption: | 830 W 1/8 power |
| Frequency range: | 20 - 20000 Hz |
| Height: | 8,9 cm |
| Depths: | 46,1 cm |
| Width: | 48,3 cm |
| Power/channel (4 Ohm): | 1100 W |
| Power/channel (8 Ohm): | 650 W |
|
10451696 PSSO QCA-6400 4-Channel SMPS Amplifier |
|
| Power supply: | 230 V AC, 50 Hz |
| Power output (RMS): | |
| 2 ohms | 4 x 1600 W |
| 4 ohms | 4 x 1400 W |
| 8 ohms | 4 x 800 W |
| 4 ohms bridged | 2 x 3200 W |
| 8 ohms bridged | 2 x 2800 W |
| Signal-to-Noise ratio: | >80 dB |
| Total harmonic distortion: | <0.05 % |
| Damping factor: | >800 |
| Slew rate: | >10 V/µsec |
| Crosstalk: | >65 dB |
| Input sensitivity: | 0.775 V/1.0 V/1.4 V/38 dB/32 dB/26 dB, switchable |
| Voltage gain: | 40.3 dB (0.775 V), 38 dB (1.0 V), 35.1 dB (1.4 V) |
| Input impedance: | 20 kohms (balanced), 10 kohms (unbalanced) |
| Input connectors: | 4 x XLR |
| Output connectors: | 4 x Speaker, 4 x XLR feed-through output |
| Protection: | Overheat, overload, short-circuit, over-current, DC voltage, softstart, VHF signals |
| Cooling: | 2 temperature-controlled fans, front-to-rear |
| Controls: | Power switch, input attenuators, mode switch stereo/parallel/bridged, input sensitivity |
| LED indicators: | Protect, clip, signal (per channel) |
| Construction: | Steel chassis, aluminum front panel |
| Dimensions: | 483 x 445 x 89 mm |
| Rack installation with 2 U | |
| Power consumption: | 820.00 W 1/8 power |
| Weight: | 15,5 kg |
| Power/channel (8 Ohm): | 800 W |
| Power/channel (4 Ohm): | 1400 W |
| Frequency range: | 20 - 20000 Hz |
| Height: | 8,9 cm |
| Depths: | 44,5 cm |
| Width: | 48,3 cm |
|
10356362 PSSO DXO-26 PRO Digital Controller |
|
| Power supply: | 100-240 V AC, 50/60 Hz |
| Analog inputs: | 2 x XLR, balanced |
| Maximum input level: | +22 dBu |
| Input impedance: | 10 kohms |
| Dynamic range: | 118 dBA |
| Digital input: | 1 x AES/EBU (XLR) |
| Input impedance: | 110 ohms |
| Outputs: | 6 x XLR, balanced |
| Output impedance: | 50 ohms (electronically balanced) |
| Output gain range: | -50 to +12 dB |
| Maximum output level: | +12 dBu |
| Dynamic range: | 118 dBA |
| Sampling frequency: | 65 kHz |
| Distortion: | 0.005 % |
| Filter types: | Bessel, Butterworth or Linkwitz-Riley |
| Slopes: | 6, 12, 18 or 24 dB/octave |
| Crossover frequency: | 20-20000 Hz |
| Delay: | 0 to 2000 ms (inputs/outputs) |
| Communication: | LAN (TCP/IP), USB type B |
| Dimensions (W x D x H): | 482 x 44 x 223 mm |
| Power consumption: | 10.00 W |
| Weight: | 2,5 kg |
| Frequency range: | 10 - 40000 Hz |
| Height: | 4,45 cm |
| Depths: | 22,3 cm |
| Width: | 48,3 cm |
|
30100150 OMNITRONIC Front Panel Z-19U-shaped, steel,black 1U |
|
| Weight: | 0.465 kg |
| Width: | 48,3 cm |
| Height: | 4,45 cm |
|
30109192 ROADINGER Rack Profi KM 8U 55cm with wheels |
|
| Strength: | 9 mm |
| Outside dimensions (W x D x H): | 530 x 710 x 520 mm |
| Inside dimensions: | |
| Mounting width: | 483 mm (19") |
| Mounting height: | 360 mm (8 U) |
| Mounting depth: | 550 mm |
| Corner dimensions: | 65 mm |
| Weight: | 21,5 kg |
| Color: | Black laminated |
| Maximum load: | 100 kg |
| Material: | Birch multiplex 9 |
| Strength: | 9 mm |